Skip to main content

Infosys Fresher Aptitude 2020 Sample Question Paper Pseudocode Answers

Given below are the answers to Infosys Fresher Aptitude 2020 Sample Question Paper Pseudocode.  Comment below if you have any doubts.  The full video is below for you to watch.
Post a Comment

Sensor Manufacturing and Process Control Week 5

 

The following image shows 4 signals in the circuit. The ground (0 volt) levels for the red, blue and green traces are all set coincidently where the blue Ch3 flag is located, 1 division from the bottom of the screen (see scale in white at right).

The gain for the yellow trace (Ch 4, top) is set to 2 v/div and it’s ground level is located 3 divisions from the top of the screen (see scale in yellow).

The power supply voltage for the motor is 4.3 volts. Each of these signals appears at one of the GPIO pins.

1. Green

2. Red

3. ----

4. 0.2 amps

5. Blue

6. Yellow

7. 310 amps

8. 2 amps

9. yes

10. true

11. -----

12. it decreases

13. -----

14. it allows the code to read the peak current

15. -----

he following image shows 4 signals in the circuit.  The ground (0 volt) levels for the red, blue and green traces are all set coincidently where the blue Ch3 flag is located, 1 division from the bottom of the screen (see scale in white at right). 

The gain for the yellow trace (Ch 4, top) is set to 2 v/div and its ground level is located 3 divisions from the top of the screen (see scale in yellow). 

Because the Nscope will clip signals above 5 volts (and in fact the trace may disappear), the power supply voltage for the motor is 4.3 volts to stay below this limit. 

Each of these signals appears at one of the PSoC GPIO pins.

The signals shown above come from the following PSoC circuit

If the gain of the PGA were increased, what would be the effect of the motor current for a given DAC value?

There would be less average current

Labels:

Comments

Post a Comment

Popular posts from this blog

Motors and Motor Circuits Week 1 Quiz Answers

Part 1 of Motors and Motor Circuits Week 1 Quiz Answers
Post a Comment
Read more

Motor and Motor Control Circuits Course Project 1 Quiz Answers

Motor and Motor Control Circuits Course Project 1 Quiz Answers ....Refer to our video lab on specifying a DC motor speed measurement. How does an FET work? Comment your answer below .... Refer to our video lab on specifying a DC motor speed measurement. How do you measure back EMF directly? It is not possible to measure the back EMF directly ....Refer to our video lab on specifying a DC motor speed measurement. Sup. pose the motor resistance is 2 ohms, motor inductance is 5 milli-henries, external voltage is 5 volts, and the back EMF time constant is .009 per RPM. As the motor accelerates, what is the motor current in milliamps at time t = 20 milliseconds when the motor is running at 500 RPM. Ignore any oscillation of the back EMF voltage due to commutation. Type an integer value of milli-amps. 250 ....Refer to our video lab on specifying a DC motor speed measurement. Why does the frequency of ripples in the de caying DC current signal increase as the motor speeds up? Select all that a...
Post a Comment
Read more

Motor and Motor Control Circuits Week 3 Coursera Quiz Answers

Motor and Motor Control Circuits Week 3 Coursera Quiz Answers 1. What causes a motor to generate back emf? The armature windings rotate through the magnetic field created by the field windings. They then become a generator, creating a current in the opposite direction to the applied current 2. What is the power in horsepower of a DC motor operating at 1000 RPM and 2 lb-ft torque? (Type in a two-decimal number.) 0.38 3. Which of the following are causes of energy loss in a DC motor? Select all that apply. Current flow in the armature and field windings Magnetic hysteresis in the iron core Eddy current losses in the field windings 4. What is true about the speed of a shunt wound DC motor? Select all that apply. The speed is proportional to the square of the armature resistance The speed is inversely proportional to the magnetic flux 6. What is true about a permanent magnet DC motor? Items (1), (2), and (4) 7. Where might the motor control circuitry be located in a servomotor? In a separa...
6 comments
Read more